Only one of the two that I got fit but they cover up the AC/heat vents under the driver and passenger seat. The intent is to keep debris from going inside of them
Ram Heavy Duty Forum
Register a free account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members through your own private inbox!
What did you do TO your RAM today?
- Thread starter LamboTexas
- Start date
mdsonofthesouth
Member
- Messages
- 49
- Reaction score
- 73
- Points
- 18
They were just vinyl or plastic stickers and only left behind a little bit of slightly hardened goo.
One of many easter eggs to be found, depending on model and trim...
Looks like the ones a vendor on 5thgenrams sells.
BigRigWrecker
Member
- Messages
- 39
- Reaction score
- 30
- Points
- 8
BigHorn3500
Active Member
I have 4 of them on my 3500,they perform great. You will be happy with them I think.
mdsonofthesouth
Member
- Messages
- 49
- Reaction score
- 73
- Points
- 18
Thought that was cool as hell when I found it in my 2500, also neat to have all the info on the underside of the armrest. Neat to take ram trucks past to present with you
While I LOVE my black with night package, Im insanely jealous of that green. Have always wanted a green truck and could never find one that checked all my boxes.
H3LZSN1P3R
You're doing it wrong
Did some plowing as usual
CdnHO
Well-Known Member
I’m sure glad that I’m in South Texas for the winter. Hate that white stuff.
LoneRanger
New Member
Plugged in my dangling cord to the engine block heater element (thanks to another thread on this forum) which the dealer failed to do in "pre-delivery inspection".
wrvond
Well-Known Member
On mine the divider flips up and seems to be quite a bit wider. I’m going to have to take another look at it.
dieselscout80
Well-Known Member
- Messages
- 1,057
- Reaction score
- 715
- Points
- 113
Where did you get that drawer from?
Fantastipotamus
Active Member
These look great! Been looking to maybe upgrade the factory mopar ones on my truck. Do you have another photo/photos from further away? They seem like they're higher than the mopar ones.
For reference the top of the slider is about 10 1/2 inches below the floor inside the cab. They do tuck up tight to the body with just enough clearance to not rattle.
Fantastipotamus
Active Member
Thanks! Dethloff sounds like they're quoting 6 weeks or so for delivery, did you find that to be true? Does the quality feel like it fits the cost? They're quite pricey.
Last edited:
PIMCAR Removable Storage Drawer... https://www.amazon.com/dp/B0FR4STXGF?ref=ppx_pop_mob_ap_share
MegaRed
Well-Known Member
Changed oil and oil/fuel filters.
I buggered up the cap on the rear filter/water separator. I looked for a billet replacement but only found caps without the drain valve. Anyone have a source to a cap with a drain?
On a side note, I also confirmed that an 1 1/8" socket is not the same as a 28mm...
I buggered up the cap on the rear filter/water separator. I looked for a billet replacement but only found caps without the drain valve. Anyone have a source to a cap with a drain?
On a side note, I also confirmed that an 1 1/8" socket is not the same as a 28mm...
He was making a run of them when I ordered so he had them all done for me in about 2 weeks. I also arranged to have him install them. He designs, fabricates and does all the welds himself and the quality is as good you can get IMO. His shop is clean and very well organized. He has a few other products in the works. I have all the skid plates he makes and everyon of them has been very robust and fit perfectly. He has a jig built so they are all built exactly the same. Heavy wall tube on everything.
Last edited:
