What's new
By:
Ram Heavy Duty Forum

Register a free account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members through your own private inbox!

AlfaOBD

Jimmy07 said:
No, but you can just use the standard manual method- key in run with seatbelt buckled, unbuckle/buckle three times.
Click to expand...

I thought it was also in the BCM as a setting? I seem to recall it toggled to disabled when I did the manual seatbelt method.
 
Brutal_HO said:
I thought it was also in the BCM as a setting? I seem to recall it toggled to disabled when I did the manual seatbelt method.
Click to expand...
It’s a setting while connected to the instrument cluster. On the 2019+ trucks it comes back parameters out of range when trying to disable it.
 
Crusty old shellback said:
Not sure that can be turned off. I just use a seat belt extender and plug that in to stop the chime when I'm off road bouncing around and get tired of the seat belt tightening up, so I take it off.
Click to expand...
@iflyskyhigh

RAM has had a way to disable that chime for years without a dealer visit or AlpgaOBD. Get in, close the door. Put seat belt on. Put truck to RUN without starting. Disconnect seat belt, reconnect, disconnect, reconnect, disconnect, reconnect (within 30” I think) then turn truck off. If done right there will be a single chime when you turn it off.
 
Do you have to do that every time you before you start the truck?

If so, lot easier to just buy the seat belt extender and plug it in and leave it.
 
Can the honks when exiting with fob while the truck is running be disabled with alphaOBD or some other method. havent had the truck for 12 hours and already irritated by the honking……
 
BraveSamWise said:
Can the honks when exiting with fob while the truck is running be disabled with alphaOBD or some other method. havent had the truck for 12 hours and already irritated by the honking……
Click to expand...
Does not look like it. There is a thread about there here:

hdrams.com

Horn beeps 3 times when exiting cab with key - engine running

Just traded my 2019 2500 Laramie for a 22 3500 Laramie. On the 2019, I could get out of the truck with engine running and lock the door with the button on the outside door handle, and all was good. On this new 2022 one, the horn beeps 3 times when I get out and close the door with the engine...
hdrams.com hdrams.com
 
snayte said:
Does not look like it. There is a thread about there here:

hdrams.com

Horn beeps 3 times when exiting cab with key - engine running

Just traded my 2019 2500 Laramie for a 22 3500 Laramie. On the 2019, I could get out of the truck with engine running and lock the door with the button on the outside door handle, and all was good. On this new 2022 one, the horn beeps 3 times when I get out and close the door with the engine...
hdrams.com hdrams.com
Click to expand...
Thanks for the link. Kinda really bums me out.
 
Jimmy07 said:
Connect to the instrument cluster > MY2013+ powernet > active diagnostics (car with hood open) > program customer features > fleet pin reset
Click to expand...
Jimmy,

I only have 2 options there. Seatbelt alert system and Lifetime engine hours. I don't see fleet pin reset
2021 Ram 2500 Limited Diesel
 
Jimmy07 said:
Go into the settings up top, then check the box that says do not verify ECU. Then connect to MY2013+ powernet instrument cluster. It should show up then.
Click to expand...
I can see fleet options now. When I try to reset to 0000 it says "Conditions can not be verified, procedure terminated."
What am I doing wrong?
 
You must log in or register to reply here.
Back
Top