Search results

Thank you, that's the answer I was hoping for. When I talked with my service advisor this morning I asked about it but he didn't seem very knowledgeable about the details, just that they had to update the programing because of the change from the CP4 to CP3. Also said I had an Emissions...

I finally broke down and scheduled the fuel pump replacement for my 2019 2500 and had a question for those that been through it already. I've made several changes to my truck that required changing settings in the BCM and I'm assuming that during the process the various computers will get reset...

Thank you, my FCA/Ram part number reading skills are limited but improving slowly.

Regarding the center console base for vin 3C7WRDBJ0KG550510, I received part number 6WX73HL1AA and it is beige while the original console is black. The 6WX73HL1AA is shown replacing 6WX731X7AA, the 6WX73TX7AA appears to be a current part number but revision AB. If anyone can tell me for sure if...

I'm looking for front and rear door panels for 3C7WRDBJ0KG550510,

Thank you sir.

Wondering if the door panels from a 4.5 gen 1500 will work in a 2109 2500. Just swapped seats and would like to change the panels to something that matches but used 4.5's are much harder to find than the 4th gen's.

I'm looking for the center console base for 3C7WRDBJ0KG550510, I have found two part number but I'm not sure which is correct for this vin. Thanks for the help.

Settings worked perfectly, high beams are working as expected.

Yes, Smart Beam is RAM's proprietary name for Auto High Beam. The settings you had were a little different from what I found elsewhere but they were all present in alfa settings so that's promising. I'll know in the morning if they work. Appreciate the help.

I finally got around to swapping out my mirror (2019 RAM 2500 Bighorn) for the Smart Beam Mirror and having one problem. I found a listing of BCM change on the Google Doc for Know Alfa Setting but can't locate one of the setting in alfa under Body computer MY2019 PowerNet. The item in question...

I picked up a regular non-digital auto dimming smart beam mirror off ebay reasonably cheap. It showed up making a distinct rattling sound like broken glass inside so I decided to go ahead and open it up and take a look. The ribbon cable from the smart beam sensor plugs into the back of the...

Thank you sir for the almost instant response. Wanted to make sure I had everything in order to get the leds working before swapping out the lights.

Ok, I've read through this thread several time and have found the BCM Settings for the LED Reflector headlights but not for the LED Projector lights. If anyone has them handy would greatly appreciate it. Also do I need to add a fuse for the C6 28 connection for Jimmy's headlight harness.

These are the instructions that came with mine. It's been a while since I bought so it possible wire colors and or labels might have changed. Also note connects are different for HD's and 1500's.

I'm getting ready to make the BCM changes this weekend and have a question. I have a 2109 2500, when I pull up the Body Computer setting for a MY2019 there is no VehConfig 8. Goes straight from VehConfig 7 to ECU settings. Assuming I need to use the MY2020 in order to access the VehConfig 8...

They both go to the Green/White can bus block behind light switch.

Looking for Drivers Front Door Panel and Switch for these two vin's, 3C6UR5DL6KG675477, 3C6UR5FL5KG615672.

I swapped out my tail lights this morning (halogen to led w/BSM). Put them in, checked all the functions and everything worked fine. Made changes to BCM and when I tested again the right turn signal dash indicator and right mirror turn light were blinking about twice as fast as the front and...

I am looking at doing this on a 2019 Ram 2500 Big Horn w/halogen tail lights. I found part numbers for the 2019 led lights on a 4th gen thread at ramforum.com. I verified that pin 7 on Module -Door-Driver-C2 was empty. The part numbers for the tail light jumpers and mirror glass in post #21 of...