Register a free account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members through your own private inbox!
My 2019 did the same thing. Dealer did a manual regen but it kept doing a burn every day. Eventually I emptied the DEF fluid, refilled and cleaned the DEF injector. I was surprised at all the white crystals almost blocking the injector. Sprayed the injector with water and it cleaned up...
I fitted lithium in tub and ran 2 gauge (35mm) from Uber the bonnet to the dc2dc charger. Using 200amp circuit breaker on positive battery. Neg cable connected to neg post of battery.
The dc2dc is fitted in tub next to battery. It has 70amp breaker on input, output and 40amp on solar input...
My truck did not have the cabling to the PDC. I ended up running a length of trailer cabling (7 core) because thats what I had. Soldered (splice joint) this to the plug at the back of the switch assembly on the cable side and ran this through the firewall.
you could wire this to the small PDC...
DPF blocked after country run towing. Dealer said bad DEF and plugged in their computer to force a burn. Did not clear so they forced another burn using new DPF fitted option. Drained DEF and refilled, tested and seems ok. Drove another 2000 miles and DPF blocked again. Engine light on and...
DEF is a source of ammonia NH3, injected post DPF where it is heated in the catalytic converter to convert nitrogen oxide NOx to water H2O vapour and nitrogen N2. It also has CO2 component. This is what they call SCR technology. The EGR is also part of the SCR technology and these all work to...
query for the brains trust. I have the same wheels fitted to the trailer and the truck. I was hoping to be able to interchange the wheels. Can the sensor (68516743AA) be used for the truck as well as the trailer or is it only able to be used for the trailer.
I picked up some genuine rims/tyres but the TMPS were removed. I am looking to replace the spare with the alloy rim and fit a TMPS sensor. Can anyone confirm if the sensors on the 2500 are the same as those listed on the first post ”The kit for the TPMS sensors (4) for trailer wheels is...
DEF reflashed.
Travelled 1025 miles (not towing) and used 4 gallons def (246 mpg).
Used 57 gallons of diesel (17.9 mpg). Thats a heap more than the quoted 3%.
Sorry, above probably wrong thread.
Yesterday Advanced ICE fitted their mapping which includes street and off road mapping. This also came with a trailer reversing camera option. As my Ram did not have the trailer reversing camera fitted I ticked that option. I ran the supplied cable from...
Mine did not have the cabling from the aux switch wired through to the PDC. I ran a seven core trailer cable, spliced into the truck side of the Aux Switch assembly plug (XY125) and ran this to a number of automobile relays under the bonnet. I found I needed to run battery to the relay...
Sway (yaw) has many interesting aspects and not all are apparent. Most think it’s ball weight which is not entirely true. The most common cause is weight behind the centre of the wheels and could be solved by moving weight closer to the wheels or adjustment of tyre pressure.
My van is 9k...
I am using 1 gallon per 438 miles. This is averaged over the last 3000miles. The dealer said they would flash the ecu. It was fine until it had its first service. I was towing a 9k trailer most of the time. Seems way over the top and it’s had the recalls.
The Upfitter cabling was not included in my 2500 and the PDC had vacant slots (no cables). Fitted the 6 AUX switch assembly, spliced into each AUX sense wire at the back of the Aux Switch Bank Upper D2321A where the wires exist the connector going to XY125A. The splice was six inches away from...
had a look at the Aux PDC and the aux 1-6 cables not present. I cannot physically get to XY125A so my options are limited. Will have to run a cable from the Aux PDC and splice into the cable where it plugs into the aux switch bank D2321A. Then it’s chase the bits to install the relays and...
Been trying to look under the aux pdc but cant seem to find the clips to release the relay/fuse holder. I was looking to wire in some additional fuses/relays. Any clues??
That's the one, Jimmy you are a life saver. Thanks again for your kind assistance. Will post how it all goes, the replacement switch is on order so I can at least wire the rest.
Sorry, I stuffed up. Thank you I do need the one posted and I am also trying to find the cables to connect in the relays for the AUX 1 - AUX 6 switches. The diagram had this labelled as 125A. Sorry for mucking you about. Appreciate your kind assistance.