What did you do TO your RAM today?

[DeepH20Driller]

I watched a you tube video that said 1/2" ID for the front and 3/8" ID for the back. However the 3/8" ID tubing didn't fit tight so had to hold it up there while draining, I need to measure and get a smaller ID.

Video I watched said to use 5/16” id hose. I haven’t gotten to try it yet. My first filter change is in a month or 2.


Sent from my iPhone using Tapatalk

 

[DeepH20Driller]

Install was easy and took about 20 or 30 minutes. BAK has improved the design and the X4S apparently took care of an issue several customers had.

I like the latch system better than all of the other brands and types of covers I've owned. It fits well.

The aluminum slats seem sturdy and the matte vinyl cover goes well with my midnight edition.
View attachment 21669View attachment 21670View attachment 21671View attachment 21672

After having 4 different hard tri-fold covers, I’m thinking of going this route next, on the new truck. I’d love to see one in person. I’ve owned a Gator, Toyota factory, and 2 BakFlip MX4’s.


Sent from my iPhone using Tapatalk

 

[NHOverland]

what all does the duel battery set up entail? Isolator? How does it deal with the intelligent battery sensor thing?

I am offering and running the Redarc BCDC1240D it is designed to work with "smart alternators" to keep the auxiliary battery charged. You can order just the mount, the mount with BCDC1240D, and the mount the BCDC1240D and 60amp fuse kit.

 

[DeepH20Driller]

Install was easy and took about 20 or 30 minutes. BAK has improved the design and the X4S apparently took care of an issue several customers had.

I like the latch system better than all of the other brands and types of covers I've owned. It fits well.

The aluminum slats seem sturdy and the matte vinyl cover goes well with my midnight edition.
View attachment 21669View attachment 21670View attachment 21671View attachment 21672

Is there only 2 positions as far as riding down the road, closed or fully open? Can you ride with it in any position?


Sent from my iPhone using Tapatalk

 

[FrancisGagne]

Bought and installed a Side by Side ramp


Sent from my iPhone using Tapatalk

 

[steve49]

Video I watched said to use 5/16” id hose. I haven’t gotten to try it yet. My first filter change is in a month or 2.


Sent from my iPhone using Tapatalk

Thanks I'll get the 5/16" and give it a try!

 

[McHenry2500]

Bought and installed a Side by Side ramp


Sent from my iPhone using Tapatalk

How does the truck ride going down the road with the SXS on the back? Any noticeable change in ride comfort or handling?

 

[Sponge60]

Is there only 2 positions as far as riding down the road, closed or fully open? Can you ride with it in any position?


Sent from my iPhone using Tapatalk

Yes, only options are open fully, or closed.

 

[AZ Sooner]

Picked up a new toy hauler today, truck pulled it awesome.

 

[Surf2snow1]

Picked up a new toy hauler today, truck pulled it awesome.

Looking good. Did you get airbags or Timbrens with the Carli setup?

 

[AZ Sooner]

Looking good. Did you get airbags or Timbrens with the Carli setup?

Thanks, I have the auto leveler from factory but I also put the Carli Leaf spring option on it. From Carli website
"Converts rear to full progressive leaf spring design - 2" Rear Lift, Matches a 3" Front Suspension Lift"

 

[Scooter29]

Loaded up our new to us camper for a night. Truck handles it well just need something to help with a tiny bit of sag and swaying off-road and big uneaven bumps. Got 2.5 in between bumps and axle.

 

[Brutal_HO]

Loaded up our new to us camper for a night. Truck handles it well just need something to help with a tiny bit of sag and swaying off-road and big uneaven bumps. Got 2.5 in between bumps and axle.

Airbags (my preference) or some like Timbrens (not a fan).

 

[Scooter29]

Airbags (my preference) or some like Timbrens (not a fan).

Looking to retain factory ride unloaded also. Timbrens from what I measured would basically be in contact unloaded so not wanting that. Airbag route I would possibly look at the daystar cradle route I’ve seen some post about so unloaded I’m keeping the stock ride.

 

[FrancisGagne]

@McHenry2500
It’s not to bad, a little sway side to side and a little lighter on the front end but nothing to bad


Sent from my iPhone using Tapatalk

 

[Jargueta16335]

Installed the Baja Designs SAE fog lights and the Baja Designs S8 light bar. Extremely happy with the light output and with the look.

 

[Great Pumpkin]

I have to admit it’s been a while. Way back I did the color matched line-x. Since then I’ve added the power steps, WeighSafe hitch, Motiv Rims with Michelin Defenders, and Mopar mud flaps. I’m still deciding on exhaust and intake mods but does anyone else have issues with the blue shocks?

 

[Tattoosruinyourlife]

I have to admit it’s been a while. Way back I did the color matched line-x. Since then I’ve added the power steps, WeighSafe hitch, Motiv Rims with Michelin Defenders, and Mopar mud flaps. I’m still deciding on exhaust and intake mods but does anyone else have issues with the blue shocks? View attachment 21947

What color is your truck? The lighting makes it look so good.

 

[Great Pumpkin]

What color is your truck? The lighting makes it look so good.

It’s the Molten Orange, and a bit of the golden hour.

 

[ShadowMTN]

I have to admit it’s been a while. Way back I did the color matched line-x. Since then I’ve added the power steps, WeighSafe hitch, Motiv Rims with Michelin Defenders, and Mopar mud flaps. I’m still deciding on exhaust and intake mods but does anyone else have issues with the blue shocks?

Yeah those shocks. Not a fan of the blue on my Wagon either. Mind posting the part number on the mud flaps?